60 mm large-shaft fixtures and industrial machinery
EP-SCS60 is a single-split aluminum shaft clamp with a 60 mm nominal bore, 95 mm outside diameter, 22 mm width and M10 clamp screw. It is intended for axial positioning and stop duties on round shafts where a clamp-style collar gives the installer a removable, repositionable mechanical reference.
Where EP-SCS60 Fits Best
The 60 mm bore is the largest standard size in the EP-SCS size chart. With a 95 mm outside diameter, 22 mm width and M10 clamp screw, it should be integrated as a purposeful machine component with adequate surrounding structure and service space.
EP-SCS60 belongs to the larger-bore portion of the EP-SCS range and should be reviewed as part of the complete machine interface rather than as a bore-only item. Its 95 mm outside diameter and 22 mm width make radial space, axial space and service access increasingly important in machinery and retrofit layouts.
Model Dimensions
| Model | Bore d | OD D | Width B | Screw M | Split W | Keyway K |
|---|---|---|---|---|---|---|
| EP-SCS60 | 60 mm | 95 mm | 22 mm | M10 | 3 mm | 18 mm |
Selection starts with the measured shaft diameter, then moves to the surrounding envelope. Confirm the 95 mm outside diameter, 22 mm axial width and access to the M10 screw against the real assembly before treating EP-SCS60 as a replacement or new-build fit.
Interface Review
For this size, define the actual axial duty and any impact condition rather than assuming holding capability from geometry. The size chart does not publish one universal holding-force rating, so demanding service should be reviewed from application data.
The EP-SCS chart lists K = 18 mm for the keyed option on EP-SCS60, while the standard collar is supplied without a keyway. A keyed request should include the mating key and shaft details because the K value is only one dimension of the complete interface.
Typical Positioning Roles
EP-SCS60 can serve as a removable stop on a 60 mm guide shaft, an axial reference beside another shaft-mounted component, or one side of a paired locating arrangement. Its 22 mm body width and 95 mm outside diameter must fit the surrounding mechanism; bearings, couplings, keys and other functional components should continue to perform the duties assigned to them by the machine design.
If EP-SCS60 is intended to act as a hard stop rather than a setup reference, describe the contact event in the enquiry. Repeated impact on a 60 mm shaft creates a different selection question from occasional positioning, even though the listed collar dimensions are unchanged.
Installation and Service Considerations
A large collar can become part of the maintenance access plan. Confirm that operators can reach the clamp screw, inspect the shaft surface and remove the collar without dismantling unrelated machine components.
For the larger EP-SCS60 interface, reserve working space around the M10 screw as well as the full 95 mm radial envelope and 22 mm body width. If the 60 mm shaft stop will see repeated impact, meaningful axial demand or another demanding duty, state that condition in the RFQ so it can be reviewed for this configuration.
The EP-SCS60 body is tightened through its M10 clamp screw and the listed split W is 3 mm. Install it on a clean 60 mm shaft, seat the collar squarely, keep the screw accessible, and verify the axial position again after tightening before the mechanism returns to service.
Configuration Details to Confirm
The size chart defines the core geometry for EP-SCS60. If the application depends on a specific tightening torque, axial holding requirement, aluminum grade, surface treatment or compliance document, state that requirement in the RFQ so it can be confirmed for the ordered configuration rather than assumed from bore size alone.
When EP-SCS60 is being considered as a replacement, record the actual shaft diameter together with the old collar outside diameter, width and screw orientation. Also note nearby shoulders, bearing hardware and visible shaft condition so the 95 mm × 22 mm envelope can be checked against the installation rather than inferred from the machine name.
Nearest EP-SCS Bore Options
EP-SCS60 is centered on a 60 mm shaft interface. Nearby catalogue entries such as EP-SCS50 and EP-SCS45 are useful for comparing the range, but they should not be used to compensate for an uncertain shaft measurement. Verify the shaft first, then treat the 95 mm OD and 22 mm width as separate envelope checks.
RFQ Focus for EP-SCS60
Send a dimensioned drawing, quantity, shaft measurement, available 95 mm radial envelope, and any keyway requirement. The listed 18 mm K value is only one interface dimension and should be checked with the mating key/shaft geometry.
For EP-SCS60, identify whether the collar will be a fixed stop, adjustable setup reference, paired locator or keyed interface. Include that role with the 60 mm shaft dimension, quantity and any restricted 95 mm OD / 22 mm width envelope so the quotation addresses the real assembly.